GSX - Refurbished GST
The GSX provides a low cost alternative to our flagship DTX system, while still providing many of the DTX's advanced features, and is available as an upgrade to your existing GST or through the purchase of a factory refurbished GSX system.
As the GSX is built upon existing systems and does not require the manufacturing of a new machine, it is also an excellent option for organizations that are focused on environmental impact.
The GSX includes an upgrade to Microsoft's Windows 10 operating system allowing for increased system support both by Microsoft and Dynatex.
Additional features of the GSX include:
- High precision production and R&D functionality
- Automatic Mode for load and run processing
- Interactive/Semi-Automatic mode for operator controlled sequencing/processing
- User friendly GUI for ease of process setup/use
- Integrated scribe and break stages
- Multiple break types/assemblies available
- Up to 150 mm wafer and small piece processing
SpecificationsPlatformDiamond Scribe Modules
Wafer Size GSX-100 / GSX-150
100 mm / 150 mm Dia.
X Y Stage Resolution 0.25 micron (Hi Resolution System)
1 micron minimum step (accuracy)
Theta stage resolution 0.001 degree Axis controllers Galil Multi-Axis Controller Set System Remote Access RJ45 LAN – 100 MB/s Ethernet
Allows for remote support/service and diagnostics, and process assistance.
Operator interface (Monitor #1) GUI with Keyboard/Mouse input
Operator interface (Monitor #2) Live video monitor
Live wafer/process view
Safety Locking hood; EMO switch PM Schedule 6 months (Bi- Annual)Break Modules Diamond Type Std: V-4-64 (4 Facet Heel/Toe)
Multiple diamond types available
Scribe angle Programmable
24 to 40 degrees
Scribe force Programmable
Force Range: 2 grams to 200 gramsSoftware
Impulse w/LVC Non-Contact breaking
LVC (Local Vacuum Chuck) holds wafer – no topside contact on wafer
Impulse w/Anvil Urethane Break Anvil(s)
Can break down to 2:1 Aspect Ratio
Matrix – Laser Bar Break of N x M Bar Array
Efficient Laser Bar-to-Die separationFacilities
Operating system Windows 10 Operator interface/processing GUI-based: Fully programmable process setup; Automatic and Interactive process modes
Allows for load and run automatic processing; or Interactive/Semi-Automatic operator guided processing
Wafer profiling Vision system mapping of wafer for automatic processing
Wafer profiling dynamically controls scribe start and stop points per wafer contour – this increases through-put
Step compensation Automatic realignment of scribe and break actions
Compensates for tape stretch, and part movement during processing
Theta alignment Automatic wafer/piece alignment for each axis First street set Automatic set using vision Recipe editor All process parameters are stored in the recipe file
Once a recipe is created and saved, the recipe is available for load and run
Power 120 VAC 20 amp 50/60 Hz
220 VAC 13 amp 50/60 Hz
VacuumAir 15-28 in Hg, 0.5 CFM60 – 85 PSI Gauge
381-711 torr, 234 cm3/sec
Environment 60 – 80 deg. Fahrenheit
15 – 27 deg. Celsius
Humidity 40 – 60 % Relative
Humidity (non – condensing)
Footprint 32" W X 43" D X 71" H
Allow 24" Front/Side ClearanceAlthough the information and recommendations set forth herein are presented in good faith and believed to be correct, Dynatex International makes no representations as to their completeness or accuracy. Information is supplied upon the condition that the persons receiving will make their own verification and determination as to its suitability for their purposes prior to use. In no event will Dynatex International be responsible for damages of any nature whatsoever resulting from the use of or reliance upon this information. NO REPRESENTATION OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER NATURE ARE MADE HEREUNDER WITH RESPECT TO INFORMATION OR PRODUCT TO WHICH INFORMATION REFERS.
- BioMedical devices with sensitive structures
- BioMedical Glass with coatings
- Si-Photonics III-V chips
- Laser Diode Cleaving and Matrix Bar-to-Die separation
- OptoElectronics Devices (PhotoDiodes, Modulators, etc.)
I was looking for a high quality scribing/breaking machine to cleave quantum cascade laser wafers into laser chips. I had a limited budget. The Dynatex team closely worked with me to fully understand the technical requirements for my laser fabrication processes. At the end, they offered me a refurbished system configuration within my budget that fully met my technical requirement. The system was pre-configured for wafer and chip dimensions that we had specified: a truly turn-key solution. We have been easily achieving mirror-like quality for laser facets with almost a 100% yield for the chip singulation. In addition, all our questions and concerns have been immediately addressed and we have never felt that we had to deal with technical problems alone. It is truly a pleasure to work with the Dynatex team and I strongly recommend their products to prospective buyers needing semiconductor wafer dicing equipment and/or services.